HART Version Burst Mode Block Model for recording and processing measured values Description of the blocks Configuration tool Device Description The GSD file Configuring a new device: procedure Cyclic versus Acyclic Data Cyclic Data Status Byte Diagnosis reply applies only to cyclic masters Acyclic Diagnostics Acyclic Data Transmission Level Transducer Block function groups Analog Input Function Blocks 1 and Appendix K: Software Revision History LCD menu structure Special attention must be paid to warnings and notes highlighted from the rest of the text by grey boxes.
Note: means important information about the product or that part of the operating manual. These limits are designed to.
Operation of this equipment in a residential. Note: Please follow the installation and operating procedures for a quick, trouble-free installation and to ensure the maximum accuracy and reliability of your SITRANS.
We always welcome suggestions and comments about manual content, design, and accessibility. Please direct your comments to techpubs. For other Siemens Milltronics level measurement manuals, go to: www. There is often more than one way to approach an application, and other configurations may also apply. If the example does not apply to your application, check the applicable parameter reference for the available options. If you have questions, you can access our hour hotline at: www. It is ideal for extreme dust and difficult applications.
The Easy Aimer design makes it easy to install the device and orient the signal towards the material angle of repose. The high frequency signal creates a narrow emission cone, which makes the LR quite insensitive to vessel interferences. For details see Approvals on page Note: Siemens Milltronics makes every attempt to ensure the accuracy of these specifications, but reserves the right to change them at any time.
Siemens Milltronics infrared IS Intrinsically Safe handheld programmer for hazardous and all other locations battery is non-replaceable. Use only approved, suitable sized hubs for watertight applications.
Process temperature varies with ambient temperature. Consult factory when using horn extension in applications subject to shock and vibration. Refer to. See Easy Aimer Installation on page Obstructions such as ladders, pipes, or the fill path, can cause false reflections. To avoid this, use the Polarization Reference Point to orient the device.
Note: the device can be rotated through degrees without damage to the unit. Holding the electronics enclosure firmly, loosen the Easy Aimer ball locking bolts and gently reposition the enclosure.
When the desired position is reached, retighten the 5 bolts to N m 11 to 17 Lbf-ft. For more frequent cleaning, a purging system can be installed between the flange and the horn antenna. The customer will supply the purging medium by a manual or automatic valve system. This option is only available with the universal flange for purging shown on page A replacement kit is available from your local Siemens Milltronics representative.
WARNING: The user is responsible for the selection of bolting and gasket materials which will fall within the limits of the flange and its intended use and which are suitable for the service conditions. The dust cap fits onto the end of the horn and prevents the buildup of dust and other process material inside the horn. Thoroughly clean inside the horn. If you remove the horn for easier cleaning, take care not to damage or bend the plastic emitter.
Press the cap firmly onto the horn until the ridge inside the cap snaps into position in the groove on the outside of the horn. Hand tighten the adjustable clamp supplied to secure the cap. Use a screwdriver or nut driver to tighten the clamp screw until the clamp provides an air-tight seal. Note: It is critical to ensure no moisture can be trapped inside.
Release the cover lock on the enclosure with a 3 mm Allen key and unscrew the cover. Use a screwdriver for extra leverage, if required. Loosen the cable gland and push the power cable through until it reaches the terminal strip. Connect the earth conductor of the power supply to the earth terminal on the metal bracket inside the enclosure.
Adjust the cable length so that the earth conductor would be last to disconnect if cable is pulled. Tighten the cable gland and check the strain relief pull and turn. Replace the enclosure cover and hand tighten it. The sealing ring must be clean and undamaged. Tighten the screw on the cover lock. To determine how many devices can be connected to a bus line, calculate the combined maximum current consumption of all the connected devices: Allow a current reserve for safety.
Connect the external earth terminal located between the cable glands to a ground. Use a cable with a cross-section of 2. Note: The nameplate shown is a typical example. Please check the nameplate on your device for your specific device configuration. Note: Installation shall be performed only by qualified personnel and in accordance with local governing regulations.
For use and assembly, refer to the main instructions. The equipment may be used with dust and fibers with apparatus temperature class T see table below.
The equipment has not been assessed as a safety related device as referred to by. Installation and inspection of this equipment shall be carried out by suitably trained. Components to be incorporated into or used as replacements in the equipment shall. Equipment Marking: The equipment marking contains at least the information on the product label.
See Product Nameplate on page A Quick Start wizard groups together all the settings you need. There are two ways to access the wizard:. Statistics on page 49 to access the records. Power up the instrument. The LCD displays the measurement and the default unit is meters. Post your question here in this forum.
Report abuse Libble takes abuse of its services very seriously. Product: Siemens Washing Machine Spam. Hateful or violent content For example, Anti-Semitic content, racist content, or material that could result in a violent physical act. Personal or private information For example, a credit card number, a personal identification number, or an unlisted home address. Promotion of regulated goods and services. Forumrules To achieve meaningful questions, we apply the following rules: First, read the manual; Check if your question has been asked previously; Try to ask your question as clearly as possible; Did you already try to solve the problem?
About the Siemens Siwamat XL Siemens Siwamat XL specifications. Related product manuals. What temperature should I use for my laundry? The washing label of your garment shows the recommended washing temperature. Do I need to use an anti-scaling agent for my washing machine? It is not necessary to use an anti-scaling agent. Scale deposits can be prevented by limiting washing at high temperatures and using the recommended amount of detergent per wash.
0コメント